sdfsdf

Industrial Automation | Distributed I/O Modules

FRB-200

FRB-200

2-port FRnet communication board Introduction PC-based I/O control systems are widely used in measurement and control system applications. But sometimes it is very difficult to meet the demands of critical timing control missions. As a result of the special features of FRnet, such as real I/O synchronization and fixed scan time, FRB boards can be added to PC-based systems to give additionial PLC-like control functions, with no need to mix PC-based controllers with PLCs. The FRB-200/100 is an isolated FRnet communication board. The FRB-100 has a single FRnet port, while the FRB-200 has two FRnet ports. Each FRnet port can control a maximum of 16 communication nodes, numbered from 0 to 15. Each single node of the remote I/O module can control a maximum of 16 DI/DO channels. In other words, each FRnet port can control a maximum of 128 DI and 128 DO channels. Traditional high-channel I/O cards occupy several PC slots, such as the ICPDAS PIO-D144 or DIO-144, and the bulky cables can be difficult to handle. Several FRB boards can be combined to work together to control thousands of I/O channels. Reduced cabling, lower labor costs, easy installation and higher reliability are the major advantages of an FRnet solution. Applications Industrial Automation Remote I/O control Building Automation Parking Lot Management Specifications Communication speed: 250Kbps Cyclic Scan time: 128 input/128 output points@2.88 ms Communication distance: 400m max Wire cable: (shielded) Twisted-pair cable General Specifications Power consumption: 5V DC @ 250mA(max) Operating temperature: -25¢XC ~ +75¢XC Operating humidity: 10% ~ 90% RH, non-condensing Storage temperature: -30¢XC ~ +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Dimensions: 120 mm x 90 mm Features Reduced Wiring two-wire cabling Innovative token-stream communication technology Real-time I/O synchronization capabilities Fixed cyclic scan time for deterministic control High speed distributed I/O control capabilities Memory-mapping I/O programming Easily programmable No software overhead for protocol processing 5V DC PCI-bus add-on card

$377.00

FRB-100

FRB-100

1-port FRnet communication board Introduction PC-based I/O control systems are widely used in measurement and control system applications. But sometimes it is very difficult to meet the demands of critical timing control missions. As a result of the special features of FRnet, such as real I/O synchronization and fixed scan time, FRB boards can be added to PC-based systems to give additionial PLC-like control functions, with no need to mix PC-based controlers with PLCs. The FRB-200/100 is an isolated FRnet communication board. The FRB-100 has a single FRnet port, while the FRB-200 has two FRnet ports. Each FRnet port can control a maximum of 16 communication nodes, numbered from 0 to 15. Each single node of the remote I/O module can control a maximum of 16 DI/DO channels. In other words, each FRnet port can control a maximum of 128 DI and 128 DO channels. Traditional high-channel I/O cards occupy several PC slots, such as the ICPDAS PIO-D144 or DIO-144, and the bulky cables can be difficult to handle. Several FRB boards can be combined to work together to control thousands of I/O channels. Reduced cabling, lower labor costs, easy installation and higher reliability are the major advantages of an FRnet solution. Applications Industrial Automation Remote I/O control Building Automation Parking Lot Management Specifications Communication speed: 250Kbps Cyclic Scan time: 128 input/128 output points@2.88 ms Communication distance: 400m max Wire cable: (shielded) Twisted-pair cable General Specifications Power consumption: 5V DC @ 250mA(max) Operating temperature: -25¢XC ~ +75¢XC Operating humidity: 10% ~ 90% RH, non-condensing Storage temperature: -30¢XC ~ +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Dimensions: 120 mm x 90 mm Features Reduced Wiring two-wire cabling Innovative token-stream communication technology Real-time I/O synchronization capabilities Fixed cyclic scan time for deterministic control High speed distributed I/O control capabilities Memory-mapping I/O programming Easily programmable No software overhead for protocol processing 5V DC PCI-bus add-on card

$260.00

FR-2053

FR-2053

16-channel isolated digital input with 20-pin header Introduction The FR-2053/2053T/2053S has 16-channel isolated photocoupler input, while the FR-2057/2057T/2057S has 16-channel isolated photo-coupler output. The default signal connector of FR-2053 and FR-2057 is a 20-pin header. The "T" stands for screw terminal connector and the "S" stands for 3-pin shroud connector. Each 3-pin connector has one Vcc pin, one ground and one signal pin. According to different applications, the users can choose suitable modules. The FR-2000 I/O module has an FRnet interface. The users can daisy chain several FR-2000 modules together. Via FRnet, the FR-2000 modules can extend the remote I/O control of PC, PAC, PAC and PLC easily. Further information about the networking of FR-2053/2057; refer to literature related to I-7188EF, I-8122, FRB-100/200. Applications Industrial Automation Remote I/O control Wire-saving application Built-in Wire-saving FRnet DI/DO control Specifications 2-wire cabling: CPEV 0.9 (2P twisted-pair cable), When different cables are used, the transmission distance may change. Power consumption: 2.0 W (Max.) Operating temperature: -25¢XC to +75¢XC Operating humidity: 10% ~ 95% RH, non-condensing Storage temperature: -30¢XC to +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Weight: approximately 120g Dimensions: 99 mm x 32 mm x 83 mm Input points: 16 points Input current: less than 6mA/channel Input impedance: approximately 4.1 kΩ Digital Level 0: 3V max. Digital Level 1: 24 +/- 10% On delay time: less than 1.0ms Off delay time: less than 1.0ms Features Built-in Wire-saving FRnet DI/DO control High-speed transmission reliability Simple synchronization mechanism No software overhead on protocol processing Supporting broadcasting (1:n data transmission) Duplicating output easily Fixed I/O scan-time and I/O synchronization DIN-Rail mountable

$244.00

FR-2053T

FR-2053T

16-channel isolated digital input module with 20-pin screw terminal connector Introduction The FR-2053/2053T/2053S has 16-channel isolated photocoupler input, while the FR-2057/2057T/2057S has 16-channel isolated photo-coupler output. The default signal connector of FR-2053 and FR-2057 is a 20-pin header. The "T" stands for screw terminal connector and the "S" stands for 3-pin shroud connector. Each 3-pin connector has one Vcc pin, one ground and one signal pin. According to different applications, the users can choose suitable modules. The FR-2000 I/O module has an FRnet interface. The users can daisy chain several FR-2000 modules together. Via FRnet, the FR-2000 modules can extend the remote I/O control of PC, PAC, PAC and PLC easily. Further information about the networking of FR-2053/2057; refer to literature related to I-7188EF, I-8122, FRB-100/200. Applications Industrial Automation Remote I/O control Wire-saving application Built-in Wire-saving FRnet DI/DO control Specifications 2-wire cabling: CPEV 0.9 (2P twisted-pair cable), When different cables are used, the transmission distance may change. Power consumption: 2.0 W (Max.) Operating temperature: -25¢XC to +75¢XC Operating humidity: 10% ~ 95% RH, non-condensing Storage temperature: -30¢XC to +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Weight: approximately 120g Dimensions: 99 mm x 32 mm x 83 mm Input points: 16 points Input current: less than 6mA/channel Input impedance: approximately 4.1 kΩ Digital Level 0: 3V max. Digital Level 1: 24 +/- 10% On delay time: less than 1.0ms Off delay time: less than 1.0ms Features Built-in Wire-saving FRnet DI/DO control High-speed transmission reliability Simple synchronization mechanism No software overhead on protocol processing Supporting broadcasting (1:n data transmission) Duplicating output easily Fixed I/O scan-time and I/O synchronization DIN-Rail mountable

$260.00

FR-2057

FR-2057

16-channel isolated digital output with 20-pin header Introduction The FR-2053/2053T/2053S has 16-channel isolated photocoupler input, while the FR-2057/2057T/2057S has 16-channel isolated photo-coupler output. The default signal connector of FR-2053 and FR-2057 is a 20-pin header. The "T" stands for screw terminal connector and the "S" stands for 3-pin shroud connector. Each 3-pin connector has one Vcc pin, one ground and one signal pin. According to different applications, the users can choose suitable modules. The FR-2000 I/O module has an FRnet interface. The users can daisy chain several FR-2000 modules together. Via FRnet, the FR-2000 modules can extend the remote I/O control of PC, PAC, PAC and PLC easily. Further information about the networking of FR-2053/2057; refer to literature related to I-7188EF, I-8122, FRB-100/200. Applications Industrial Automation Remote I/O control Wire-saving application Built-in Wire-saving FRnet DI/DO control Specifications 2-wire cabling: CPEV 0.9 (2P twisted-pair cable), When different cables are used, the transmission distance may change. Power consumption: 2.0 W (Max.) Operating temperature: -25¢XC to +75¢XC Operating humidity: 10% ~ 95% RH, non-condensing Storage temperature: -30¢XC to +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Weight: approximately 120g Dimensions: 99 mm x 32 mm x 83 mm Output method: Isolated type NPN transistor open collector Output points: 16 points Output current: less than 30V@100mA/channel Load voltage: 24V max Turn-on delay time: less than 1.0ms Turn-off delay time: less than 1.5ms Features Built-in Wire-saving FRnet DI/DO control High-speed transmission reliability Simple synchronization mechanism No software overhead on protocol processing Supporting broadcasting (1:n data transmission) Duplicating output easily Fixed I/O scan-time and I/O synchronization DIN-Rail mountable

$260.00

FR-2057T

FR-2057T

16-channel isolated digital output module with 20-pin screw terminal connector Introduction The FR-2053/2053T/2053S has 16-channel isolated photocoupler input, while the FR-2057/2057T/2057S has 16-channel isolated photo-coupler output. The default signal connector of FR-2053 and FR-2057 is a 20-pin header. The "T" stands for screw terminal connector and the "S" stands for 3-pin shroud connector. Each 3-pin connector has one Vcc pin, one ground and one signal pin. According to different applications, the users can choose suitable modules. The FR-2000 I/O module has an FRnet interface. The users can daisy chain several FR-2000 modules together. Via FRnet, the FR-2000 modules can extend the remote I/O control of PC, PAC, PAC and PLC easily. Further information about the networking of FR-2053/2057; refer to literature related to I-7188EF, I-8122, FRB-100/200. Applications Industrial Automation Remote I/O control Wire-saving application Built-in Wire-saving FRnet DI/DO control Specifications 2-wire cabling: CPEV 0.9 (2P twisted-pair cable), When different cables are used, the transmission distance may change. Power consumption: 2.0 W (Max.) Operating temperature: -25¢XC to +75¢XC Operating humidity: 10% ~ 95% RH, non-condensing Storage temperature: -30¢XC to +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Weight: approximately 120g Dimensions: 99 mm x 32 mm x 83 mm Output method: Isolated type NPN transistor open collector Output points: 16 points Output current: less than 30V@100mA/channel Load voltage: 24V max Turn-on delay time: less than 1.0ms Turn-off delay time: less than 1.5ms Features Built-in Wire-saving FRnet DI/DO control High-speed transmission reliability Simple synchronization mechanism No software overhead on protocol processing Supporting broadcasting (1:n data transmission) Duplicating output easily Fixed I/O scan-time and I/O synchronization DIN-Rail mountable

$276.00

MA-11

MA-11

Input type MagicWire for PLC Introduction The FRnet network only requires a single hostcontroller to send a token that activates all FRnet I/O modules. Two host controllers cannot be used in the same FRnet network. The MA-11, MD-11, FRB-100/200, I-7188EF, I-8122 and some FR I/O modules can be used as FRnet host-controllers. When using an MA-11, MD-11 or FR I/O module as a host-controller, the switch or jumper should be set to the A1 position. Refer to the related user's manual or literature for detailed information. When using the FRB-2000, I-7188EF or I-8122, the switch doesn't have to be set. Specifications Communication speed: 250K bps Communication distance: 400m max Digital input channels: 32 (MD-11, MD-11M) Digital output channels: 32 (MD-12, MD-12M) Connector type: 37-pin D-sub female connector (MD-11, MD-12) 37-pin D-sub male connector (MD-11M, MD-12M) Power requirements: 12~24V Wire cable: CPEV 0.9S (2P twisted-pair wire) Power consumption: 1.2 W Dimensions: 120 mm x 90 mm Operating temperature: -25¢XC ~ +75¢XC Operating humidity: 10% ~ 90% RH, non-condensing Storage temperature: -30¢XC ~ +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Dimensions: 76 mm x 73 mm x 15 mm

Call Us

MA-21

MA-21

Input type MagicWire for PLC Introduction The FRnet network only requires a single hostcontroller to send a token that activates all FRnet I/O modules. Two host controllers cannot be used in the same FRnet network. The MA-11, MD-11, FRB-100/200, I-7188EF, I-8122 and some FR I/O modules can be used as FRnet host-controllers. When using an MA-11, MD-11 or FR I/O module as a host-controller, the switch or jumper should be set to the A1 position. Refer to the related user's manual or literature for detailed information. When using the FRB-2000, I-7188EF or I-8122, the switch doesn't have to be set. Specifications Communication speed: 250K bps Communication distance: 400m max Digital input channels: 32 (MD-11, MD-11M) Digital output channels: 32 (MD-12, MD-12M) Connector type: 37-pin D-sub female connector (MD-11, MD-12) 37-pin D-sub male connector (MD-11M, MD-12M) Power requirements: 12~24V Wire cable: CPEV 0.9S (2P twisted-pair wire) Power consumption: 1.2 W Dimensions: 120 mm x 90 mm Operating temperature: -25¢XC ~ +75¢XC Operating humidity: 10% ~ 90% RH, non-condensing Storage temperature: -30¢XC ~ +85¢XC Storage humidity: 5% ~ 95% RH, non-condensing Dimensions: 76 mm x 73 mm x 15 mm

Call Us

  
1
 
2 
 
3 
 
4 
 
5 
 
6 
  

Refine your search

 and / or    

Send

  My Interestsss

This is our way of making your browsing experience a success. If you have any technical questions, we will make it our pleasure to review this list and find the solution that's right for you.

  While browsing, add the products you are interested in by clicking on the add to my interest buttons.

 

Need a Solutions?

We can provide the answer!